Why SST Makes Measurement Harder
A solid-state transformer (SST) replaces the iron core and windings of a conventional line-frequency transformer with power-electronic conversion stages plus a high-frequency isolation transformer. The energy is the same, but the behaviour shifts from "slowly changing at 50 Hz" to "switching at several kHz to tens of kHz".
Three consequences hit the measurement side directly: signals move to higher frequencies, waveforms are no longer clean sine waves, and AC and DC coexist in the same system. Selecting parts the way you would for a conventional CT leads to visible distortion in an SST.
- Frequency: switching frequencies reach the kHz range. Conventional CTs and low-frequency transducers lack the bandwidth, so both magnitude and phase readings drift.
- Waveform: PWM edges, ripple and transient spikes stack up. The sensor needs enough bandwidth and response speed to reproduce them.
- AC/DC coexistence: AC side, DC bus and battery side exist at once, so the sensor must handle DC components — exactly where fluxgate and closed-loop Hall devices excel.
- Integration: higher frequency means a more compact device, leaving less space, smaller bushing windows and less thermal margin for the sensor.
Engineering note: in an SST project, "reading something" and "reading it accurately" are two different things. Confirm the frequency content and the maximum value of the measured signal (transients included) before you compare accuracy specs — otherwise the selected model works on the bench and drifts in the field.
Four Scenarios, Four Sets of Priorities
AI Data Centers
Rack power density keeps climbing, and supply architectures combining HVDC distribution with SST are being adopted more widely. Measurement focuses on DC bus current, branch distribution and insulation monitoring. Cabinet space is tight, so PCB-integrated or compact bushing designs are preferred.
Energy Storage
The power conversion system (PCS) handles bidirectional energy flow between battery and grid. Current reverses with charge/discharge, so the sensor must measure both directions and cope with two very different conditions: low voltage with high current on the battery side, high voltage with lower current on the grid side.
High-Power Charging
High-power charging delivers hundreds of amps or more in a short window. Bus current is large and temperature rise is significant, which puts the emphasis on range headroom and high-temperature stability.
Smart Microgrids
Microgrids convert between AC, DC and multiple voltage levels. Every node needs comparable, time-aligned measurement data; without it, coordinated control and state assessment are impossible.
What all four share: accurate sensing and real-time monitoring of electrical parameters have moved from optional to part of the control loop. That is why sensor selection now happens at the architecture stage in SST projects.
Where Current Sensors Go, and How to Specify Them
Breaking the system down by measurement location makes the decision much clearer. The table below maps positions to technologies across the CHIPSENSE current and voltage sensor range.
| Location | Typical range | Recommended technology | Representative series | Key point |
|---|---|---|---|---|
| Grid side / input stage | 50–5000 A | Closed-loop Hall | CR8A, CM9A, CM5A | Large window, bolt mount, check mechanical strength |
| Around HF isolation | 6–100 A | Closed-loop Hall (wide bandwidth) | CR1V, CN1A, CN2A | 200 kHz bandwidth, watch response |
| DC bus | 300–700 A | Fluxgate (CAN output) | FR1C | Digital output removes one analogue chain |
| Branch / on-board | 25–100 A | PCB closed-loop / ASIC | CN2A, AN4VA | Single supply, ratiometric output |
| Insulation monitoring / micro current | 5 mA–0.3 A | Fluxgate | FR2V, FR7V, FR8V | Resolution and drift at micro current |
For example, CR8A M00 covers 500–5000 A with a Ø120 mm window and M6 bolt mounting, ±0.3% accuracy, 100 kHz bandwidth, -45~85 °C operating range and ±15~24 V supply — built for busbar current sensing in high-power modules. Where accuracy matters more at the same range, CM9A H01 reaches ±0.1% at 5000 A with 100 kHz bandwidth and a Ø94 mm window.
Digital interfaces are increasingly valuable in SST. The FR1C series outputs CAN directly at 300–700 A, runs on 12 V or 24 V, has a Ø24.4 mm window and operates from -40~85 °C — removing one analogue acquisition chain along with its noise and wiring problems.
Tip: for high-current positions, verify window size against busbar dimensions and check that bolt mounting can carry the mechanical load. A Ø120 mm window often eliminates the need to dismantle busbars in retrofit projects.
Voltage Side: Covering 20 V to 2000 V
An SST system spans several voltage levels, and voltage measurement normally comes in pairs with current measurement for power calculation and bus supervision.
- Medium/high voltage: the VN4A series covers 500 V, 750 V, 1500 V and 2000 V with ±0.5% accuracy, ±15…24 V supply and ±50 mA output, suited to DC bus and grid-side voltage sensing.
- Medium/low voltage: VN1V P00 offers a 600 V range (±0.5%) plus a 1 mA signal version; VN4V P00 targets 48 V systems with a 5 V single supply and 2.5±2 V ratiometric output for direct ADC sampling.
- Control side: VN2A handles mA-level signals (5 mA / 10 mA); VN4VA PB00 delivers 4–20 mA at 20 V, plugging straight into standard PLC analogue modules.
Specify voltage sensors in the reverse order: fix the voltage level and the insulation requirement at the mounting position first, then the output form, and only then compare accuracy and temperature range. Voltage outputs must match the DAQ input range, current outputs need a defined burden resistance and noise immunity, and 4–20 mA suits long-distance transmission.
Six Parameters That Decide Whether It Works
- Range: size for the maximum measured value including transients, not for the nominal rating.
- Accuracy: check whether it is room-temperature or full-temperature-range. SST internals run hot, so use the full-range figure.
- Bandwidth: cover at least the highest frequency component you need to preserve. 100 kHz is enough for most power-electronics work; below 50 kHz needs careful justification.
- Response time: wherever protection acts, response time matters as much as bandwidth — do not look at bandwidth alone.
- Operating temperature: select against measured extremes at the mounting point. -40~85 °C is typical; some positions need -45~85 °C or 125 °C and above.
- Interface and mounting: window size, busbar/PCB mounting, connector type and output form must all match the downstream acquisition circuit.
Reminder: accuracy on a datasheet is usually quoted at room temperature, rated input and steady state. Treating it as a full-condition figure is the most common cause of "measurement drift" appearing late in a project.
FAQ
Is a fluxgate sensor mandatory in SST projects? No. Fluxgate excels at micro-current and high-accuracy DC measurement, while closed-loop Hall offers a better balance of bandwidth, cost and mounting convenience for high current in the main power path. A common practical combination is closed-loop on the main path plus fluxgate on monitoring branches.
How much bandwidth is enough? Base it on the highest frequency component you need to keep, not on maximum available bandwidth. Too much bandwidth admits more noise; too little loses transients and harmonics. 100 kHz satisfies control and monitoring needs in most power-electronics systems.
PCB-integrated or bushing type? PCB-integrated parts (such as CN2A and AN4VA) are compact and suit modular, high-volume designs, but their range and withstand voltage are limited by board-level design. Bushing types (such as CR8A and CM9A) handle high current and high-voltage isolation and are easier in retrofit work. Use current level and insulation requirement as the dividing line.