In foundry, smelting, welding and heat-treatment workshops, heat sources are concentrated, radiant load is intense and workstations are fixed, so summer temperatures in the working zone often run well above outdoor levels. The recurring complaint is familiar: the company installs a great deal of ventilation equipment, spends the money, and the positions where people actually work are barely any cooler.
The reason is that the target was set wrong. Cooling an entire workshop means removing the heat load of the full volume, with equipment cost and running electricity growing in proportion to that volume. Workers, however, stay at fixed positions, so what really needs improving is the small working zone where a person stands. That is the starting point of spot cooling.
1. Identify Where the Heat Comes From
Determine the source before designing anything, because each source calls for a different measure:
- Radiant heat from equipment: melting furnaces, pouring lines, reheating furnaces, molds. It is directional, so perceived temperature far exceeds air temperature for anyone standing in the radiation path.
- Process heat release: freshly cast parts and heat-treated components keep releasing heat as they cool, raising the temperature of the whole area.
- Stored environmental heat: sun on roofs and exterior walls, poor ventilation letting heat accumulate and linger overnight.
- Occupant and equipment load: metabolic heat from operators plus heat from motors and hydraulic systems.
A simple field method: measure both dry-bulb temperature and globe temperature at the workstation. The gap between them indicates radiant intensity. A large gap means radiation dominates, so focus on shielding and localized air supply; a small gap means ambient air temperature is the issue, so focus on ventilation and air exchange.
2. Three Approaches to Spot Cooling
1. Localized air supply at the workstation
For fixed positions in relatively open spaces, this is the most economical and effective option. Raising air speed around the body accelerates convective and evaporative heat loss, which improves perceived comfort substantially.
- Applies to: fixed work positions where a certain air velocity is acceptable.
- Design points: velocity high enough to matter but not enough to stir up dust or disturb the process; outlet position and angle covering the upper body; noise kept within acceptable limits.
- Typical equipment: industrial wall fans, workstation supply units, portable fans.
2. HVLS fans (high-volume, low-speed / overall circulation)
Several meters in diameter, these industrial fans move very large air volumes at very low rotational speed, producing a slow overall air movement that breaks up thermal stratification and keeps air flowing across the body surface.
- Applies to: workshops with generous ceiling height and open space, used alongside localized air supply.
- Design points: mounting height and blade diameter must suit the ceiling height; with multiple units, consider how airflow directions add to or interfere with each other; keep clear of cranes and spray zones.
- Advantages: one unit covers a large area, consumes far less power than many small fans, and noticeably improves perceived temperature.
3. Evaporative cooling (cooling and air exchange)
Using the latent heat of water evaporation, air drawn through wetted media is cooled and delivered indoors, accomplishing air exchange at the same time.
- Applies to: dry or semi-dry climates, workshops with openings, scenarios where added humidity is acceptable.
- Design points: adequate exhaust paths are mandatory to create directional "supply, pass through, exhaust" flow, otherwise humidity accumulates and performance drops; water source and water quality need treatment against scaling and microbial growth.
- Note: cooling effect is limited in humid regions, so check local summer relative humidity before selecting this route.
3. Putting Together a Combined Solution
A single measure rarely solves a heat-source workstation problem. Common combinations are:
- Radiant heat dominant: prioritize shielding the source and removing heat locally (heat screens, local exhaust hoods) to keep radiation away from the workstation, then layer localized air supply on top. This often outperforms simply increasing airflow.
- Ambient heat dominant: use a combination of HVLS fans plus evaporative cooling supply plus negative-pressure exhaust to establish directional flow that carries heat away.
- Fixed and scattered workstations: lead with localized air supply, supported by plant-wide fans. Investment concentrates where it produces direct, visible results.
4. Installation and Operation Essentials
- Design the airflow path: supply and exhaust must be considered as a pair, with air coming in and going out. Supply without exhaust creates positive pressure and stifling conditions.
- Avoid disturbing the process: in pouring, spraying and grinding areas, assess how air velocity affects the process and airborne dust.
- Safety clearance and guarding: fan blades and drive components need guards, mounting height must meet safety clearance requirements, and maintenance access must be reserved.
- Electrical and environmental fit: in hot, dusty or oily-mist environments, select motors and control enclosures with suitable ingress protection, plus overheat and phase-loss protection.
- Noise accumulation: assess the combined noise of units running together; workstation noise should meet occupational health requirements.
5. How to Verify the Results
The question a cooling project most often faces is whether it actually did anything. Use a repeatable verification method:
- 1Measurement point layout: place sensors at working height (typically the upper body of a standing operator) and set up reference points in non-supplied areas of the workshop.
- 2Parameters: dry-bulb temperature, relative humidity and air velocity; add globe temperature at workstations with strong radiation.
- 3Measurement period: choose typical high-temperature summer days, measure continuously over several days, covering morning, afternoon and evening shifts.
- 4Comparison baseline: compare against data from the same period before the retrofit, or against simultaneous reference points.
- 5Subjective feedback: collect perceived comfort ratings from operators at the workstation to corroborate the objective data.
When judging improvement, consider temperature and air velocity together. In many cases the perceived improvement comes mainly from increased air velocity and reduced radiation rather than from a large drop in air temperature. Reporting only "how many degrees it dropped" is misleading.
6. Recommended Implementation Sequence
- Step one: field measurement. Map heat source locations, workstation distribution, current temperature and air velocity, ceiling height and structure, and available power.
- Step two: define targets. Specify which workstations to improve, the target comfort level, and the allowable limits for air velocity and noise.
- Step three: small-scale pilot. Equip one or two representative workstations first, verify performance and process impact, then decide whether to scale up.
- Step four: full rollout and acceptance. Implement in bulk according to the pilot conclusions, then re-measure and accept using the agreed method.
Frequently Asked Questions
Can you guarantee the temperature it will be reduced to? A responsible answer is no — promising a specific temperature figure is not credible. Cooling performance depends on heat source intensity, workshop volume, ventilation conditions, local climate and equipment configuration. A design must follow field measurement, and acceptance must rest on measured data. Any fixed figure offered before a survey is unreliable.
Does evaporative cooling work in humid regions? Its effectiveness drops significantly. The temperature drop achievable through evaporative cooling depends on the relative humidity of the air: the higher the humidity, the less water can evaporate and the smaller the drop. Humid regions should lead with ventilation, localized air supply and radiation shielding, treating evaporative cooling as a supplement.
Do we still need exhaust after installing large fans? Yes. HVLS fans get air moving and eliminate thermal stratification, but they do not remove total heat. Getting heat out of the building still requires adequate exhaust and intake paths; only the two working together deliver sustained improvement.