Home / News / How to Build Factory Energy Monitoring: Sub-Metering and the Path to Energy Retrofits

How to Build Factory Energy Monitoring: Sub-Metering and the Path to Energy Retrofits

2026-11-01Technical Solutions9 min read
How to Build Factory Energy Monitoring: Sub-Metering and the Path to Energy Retrofits

Plenty of factories want to cut energy use, yet all they hold is a monthly electricity bill — they know the total but not the composition. Trying to save energy in that position means guessing from experience, with no way to tell afterwards whether the change achieved anything.

Online energy monitoring solves the visibility problem: breaking electricity, water and gas down by area, by asset and by shift to build a comparable, traceable data foundation. Only with that foundation in place can energy retrofits be validated and continuously optimized.

Step 1: Design the Sub-Metering Hierarchy

Metering is not a case of more meters being better. Structure it by management need, usually in three levels:

  • Level one (incoming feed / main meter): the plant's main incoming electrical feed, main water and main gas. Used to reconcile utility bills and check total balance.
  • Level two (workshop / system): independent metering for each workshop and each utility station (air compressor room, chiller plant, pump house). Used for departmental energy assessment and horizontal comparison.
  • Level three (key equipment): individual metering for large consumers such as air compressors, injection molding machines, melting furnaces and large fans and pumps. Used to locate specific savings opportunities.

Practical advice: level one is mandatory. Level two offers the best return, since it supports management assessment. Level three should target only equipment that carries a large share of consumption — covering ten to twenty units is usually enough to capture the bulk of usage.

Step 2: Hardware Specification

  • Metering instruments: make use of the smart meters equipment already has. Most modern distribution panels and drives ship with a communication port, and older panels can be retrofitted with DIN-rail meters that support communication, or with current transformers plus a power monitoring module.
  • Acquisition equipment: deploy one edge gateway per distribution room to aggregate that area's meters locally, avoiding long cable runs. In plants with many tags, deploy by zone.
  • Uplink: Ethernet within the plant; 4G or wireless where runs cross sites or cabling is impractical.
  • Platform side: an energy management system on a local server or in the cloud, handling storage, visualization, reporting and alarming.

Three things deserve the most attention during selection: whether the meters share a common protocol (prefer the Modbus standard), whether the gateway supports offline buffering (data must not break), and time synchronization (sub-metered data that is mistimed cannot be compared period to period).

Step 3: Putting the Data to Work

Installing meters is only the beginning. The value comes from four activities:

  1. 1Energy per unit of output (energy intensity): watching total consumption tells you nothing. Dividing by output gives a figure that reflects real efficiency and allows comparison across months and shifts.
  2. 2Share by category and trend: find where electricity actually goes — usually compressed air, chilling, process heating, fans and pumps — and then retrofit with a target in mind.
  3. 3Peak, flat and valley analysis: with time-of-use tariffs, identify loads that can shift to off-peak hours, such as storage, thermal storage or non-continuous process scheduling.
  4. 4Anomaly alarming: abnormal baseline load at night and on rest days, equipment idling, low power factor. These are often the easiest savings to pick up.

Common Energy-Saving Directions, from Easiest to Hardest

  • Management measures (almost no investment): eliminate idling on rest days, lower compressor pressure setpoints, zone-based lighting control, air-conditioning temperature settings. The data exposes these problems directly.
  • Control measures (moderate investment): compressor sequencing, chiller plant sequencing, variable-frequency retrofits on pumps, demand-based ventilation.
  • Equipment measures (larger investment): high-efficiency motor replacement, waste heat recovery, rooftop PV, process equipment renewal.

Reminder: every retrofit needs before-and-after data from comparable periods. Run a full cycle of baseline data for at least one month before changing anything, otherwise the effect cannot be substantiated.

Step 4: Connecting with Production Data

Looking at energy in isolation only answers "how much was used". Correlating energy with output, shift, product type and equipment state is what answers "why so much".

There are usually two ways to connect them: either the energy platform reads production figures from MES/SCADA, or the edge packages both data types together at aligned timestamps before upload. The former depends on equipment and process codes matching; the latter requires accurate time synchronization.

Five Common Pitfalls During Implementation

  • Installing meters without a hierarchy: plenty of meters but no structure, so the data cannot support performance assessment and everything has to be reorganized later.
  • Ignoring total balance verification: if the sum of sub-meters drifts persistently from the main meter, there is a wiring error or a range setting problem. Run a balance check before any analysis.
  • Unreasonable sampling interval: polling the whole plant every second generates enormous data for no benefit. One to five minutes is generally enough for energy analysis, with key assets sampled more densely.
  • Unhandled data gaps: gaps caused by outages or meter power loss go unflagged and contaminate the statistics. Missing values must be marked and repaired on the platform side.
  • No owner: reports nobody reads and alarms nobody handles leave the system idle within six months. An energy project needs a clearly accountable department and an assessment mechanism.

Phased Rollout Recommendations

  • Stage one: complete level one and level two metering and bring the platform online, delivering daily energy reports by workshop and month-over-month comparison.
  • Stage two: add level three metering on key assets, run energy-per-unit and peak/valley analysis, and push management and control measures.
  • Stage three: integrate with production data to model energy by product and by process step, supporting scheduling optimization and equipment renewal decisions.

Frequently Asked Questions

Our existing panels have no smart meters. Is retrofitting a major disruption? In most cases the work can be done without stopping production, or during a short outage. The usual approach is to add DIN-rail meters with current transformers, or to use split-core transformers to reduce rewiring. The retrofit plan has to be finalized after a site survey of panel space, busbar structure and available outage windows.

How often should energy data be sampled? One to five minutes generally satisfies analysis and assessment needs for sub-metering. Key assets where start-stop behavior matters or where faults need tracing can be sampled down to seconds. Overly dense intervals add substantial storage and network load for limited benefit.

Our sites are spread across several locations. Can they be monitored centrally? Yes. Deploy a gateway at each site for acquisition and buffering, then uplink to a unified platform over a leased line or 4G/5G. The critical requirements are a unified tag naming convention and time synchronization; without them, cross-site data cannot be compared horizontally.

Related reading

FAQ

How much energy can factory energy monitoring actually save?

It depends on the industry, equipment condition and existing management practices, so no single figure applies. The usual pattern is that management measures — eliminating idle running and optimizing setpoints — cost almost nothing and pay back quickly, while control and equipment retrofits are evaluated case by case against payback period. Each project should be calculated item by item against baseline data.

How deep should sub-metering go?

At least to workshop level (level two), which offers the best return because it supports departmental assessment and horizontal comparison. Then add level three metering for equipment carrying a large share of consumption. There is no need to meter every single asset.

Is an energy management system the same thing as an electrical monitoring system?

Not exactly. Electrical monitoring systems focus on the safety and operation of power supply and distribution, dealing with switchgear and protection devices. Energy management systems focus on energy statistics, analysis and optimization, dealing with how energy flows and how efficiently it is used. Their data sources overlap, so they can share a common acquisition layer.

Need a similar solution?

Our engineers survey site conditions and design the solution; configuration and results are based on on-site measurement.