Sources and Scope of This Case
This article is an engineering configuration example compiled from published product documentation. It is not a construction record or acceptance report for a specific customer project, and contains no customer names, project locations, measured performance figures or acceptance conclusions. All models, ranges, supply voltages, outputs and accuracies are taken directly from the sensor selection catalog parameter tables; final selection is subject to site conditions, the latest datasheets and engineer confirmation.
- DC panel basis: catalog page 9, "Sensors in Smart Grids - Substation" - the DC panel monitoring system needs sensors to measure current, leakage current, voltage, power and energy, and DC leakage sensors are used to monitor the insulation-to-ground condition of each branch.
- Energy storage basis: catalog page 9, "Distribution - Energy Storage Systems" - current sensors sense changes in battery current so the BMS can detect a short circuit; voltage sensors monitor battery voltage so the BMS can estimate state of charge and avoid overcharging.
- Battery management basis: catalog page 10, "Utilization - Battery Management" - the terminal current and voltage of each cell, plus the pack charge/discharge current and voltage, are acquired to prevent over-charge or over-discharge.
- Installation basis: catalog page 11, "Sensor Handling Precautions" (11 items); parameter basis: the series parameter tables. The catalog notes that pictures and parameters are for reference and the manufacturer reserves the right to update products without prior notice.
Why an Ordinary CT Is Not Enough on the DC Side
In DC panels and battery energy storage systems, residual current may be pure DC, pulsating DC, or a combined AC/DC waveform. The catalog singles out "DC leakage sensors for monitoring the insulation-to-ground condition of each branch" precisely because conventional AC residual-current CTs cannot cover a DC component; the leakage module entries in the catalog explicitly specify Type-B residual current detection covering DC, AC and complex waveforms.
Two further measurement requirements coexist with insulation monitoring: the BMS needs continuous charge/discharge current to detect shorts and estimate state of charge, and bus/cell voltage acquisition for over-charge protection. The three differ in range, waveform and output interface, and are normally not served by a single sensor.
- Insulation / residual current: waveform discrimination (Type B), threshold output and self-test capability; the quantity is mA-level leakage current, not main-circuit current.
- Main-circuit charge/discharge current: rated current coverage, bidirectional measurement, accuracy and temperature drift; closed-loop Hall or fluxgate solutions are typical.
- Voltage acquisition: primary rated voltage, isolation and mounting form; the catalog VN series covers PCB mount, low-primary-current, bolt-mount and 4-20 mA output variants.
Configuration A: DC Panel Branch Insulation Monitoring
The objective is on-line monitoring of the insulation-to-ground condition of each outgoing DC panel feeder, with a signal capable of driving a downstream protective action when residual current exceeds the limit. The catalog describes the DC panel monitoring system as measuring, controlling and computing on the acquired data to generate alarms, displays and control outputs, with DC leakage sensors dedicated to branch insulation monitoring.
Candidate leakage detection modules (all from the catalog's leakage module entries)
| Model (catalog name) | Form | Key capability per catalog | Typical position |
|---|---|---|---|
| CSMD1 & TR3A 6 C00 分体式漏电检测模组 | Split module + CT | Type-B residual current, DC/AC/complex waveforms, trip-level output on excess | Individual DC panel feeders |
| TR6A 32 C00 & FR1D 6 C00 一体式漏电检测模组 | Residual-current sensor + metering CT integrated | Type-B detection, low power, high immunity, single/three-phase; catalog lists charging piles and power monitoring | Circuits needing both metering and residual-current detection |
| FR1D 6 C02 剩余电流传感器 | Residual-current sensor | Type-B detection circuit, multiple leakage waveforms | Space-constrained feeders |
| FR5D 6 C00 漏电流检测传感器 | Open-loop fluxgate leakage sensor | Through-hole, DC/AC/pulsating residual current, push-pull indication above threshold, built-in test coil for self-check | Circuits requiring periodic functional self-test |
| FR5D 6 C01 漏电流检测传感器 | Open-loop fluxgate leakage sensor | Same as FR5D 6 C00, different variant | As above |
Recommended configuration order: first fix the aperture / CT size from the branch conductor dimensions; then confirm Type-B detection capability against the residual-current waveforms the system can produce; finally confirm that the output form (trip level / push-pull indication) interfaces with the downstream protection or monitoring circuit. Residual-current trip thresholds and protection coordination must be set by the electrical design based on the system earthing arrangement; the catalog gives no universal setting.
- Catalog page 11: to prevent noise interference on the output signal, use twisted-pair or shielded cable for the output wiring.
- For sensors with a through-hole, install the primary busbar filling the aperture or centred in the aperture to preserve performance.
- Other equipment generating a magnetic field nearby may change accuracy; allow clearance in the cabinet layout and verify by measurement.
Configuration B: ESS BMS Charge/Discharge Current and Voltage Sensing
Catalog page 9 ("Energy Storage Systems") and page 10 ("Battery Management") describe BMS measurement in two layers: pack main-circuit charge/discharge current, and the terminal voltage and current of each cell. Engineering practice likewise splits sensing into high-current bidirectional measurement of the main circuit and high-accuracy measurement of auxiliary / small-current circuits.
Closed-loop current sensors suit the main circuit (the catalog CM series covers 200 A to 5000 A ratings); a CAN-bus output variant is available where a digital interface is required. For small currents and leakage detection, fluxgate series with primary ratings down to 0.005 A are available. On the voltage side, select within the VN series by bus voltage class and mounting form. All parameters below are read directly from the catalog parameter tables.
Current side: real catalog model parameters
| Model (catalog name) | Primary rated range A | Supply V | Output | Accuracy | Position / note |
|---|---|---|---|---|---|
| CM1A H00 | 200 | ±12…15 | ±100mA | ±0.2 | Bidirectional pack main-circuit current, closed-loop mid-power |
| CM4A H03 | 1200 | ±24 | ±300mA | ±0.3 | Large ESS cabinet main circuit, high-current closed-loop |
| FR1C H1252A | 300-500-700 | 12 | CAN | ±0.3~0.5 | CAN bus output for digital acquisition |
| FR2V H00 | 0.01-0.02-0.05-0.1-0.2-0.3 | ±12…15 | ±5V | ±1.0 | High-accuracy small DC, fluxgate zero-flux |
| FR7V H00 | 0.005-0.01-0.2 | ±15 | ±5V | ±1.0 | Micro-current and leakage, primary down to 0.005 A |
| FR8V H00 | 0.01-0.02-0.05-0.1 | 24 | 1.5±1.5V | ±1.0 | -40 to 85 °C wide temperature, outdoor/vehicle cabinets |
Voltage side: real catalog model parameters
| Model (catalog name) | Primary rated range A | Supply V | Output | Accuracy | Position / note |
|---|---|---|---|---|---|
| VN1V P00 | 600V | ±12…15 | ±3V | ±0.5 | PCB-mount voltage sensor |
| VN2A P00 | 10mA | ±15 | ±25mA | ±0.6 | Low-primary-current voltage sensor |
| VN4A M15 | 500V-750V-1500V-2000V | ±15…24 | ±50mA | ±0.5 | High-voltage bolt-mount voltage sensor |
| VN4V P00 | 48V | 5 | 2.5±2V | ±0.5 | 48 V bus voltage sensing |
| VN4VA PB00 | 20V | 15 | 4-20mA | ±1.0 | 4–20 mA output voltage sensor |
The "primary rated range" column reproduces the catalog's multi-rating notation: the hyphen is a separator between selectable ratings, not a minus sign or a continuous interval (e.g. 0.01-0.02-0.05-0.1-0.2-0.3 means the series offers those ratings). A specific order code corresponds to one of them; refer to the datasheet.
Installation and Commissioning Notes (Catalog Page 11)
The following items are summarised item by item from catalog page 11, "Sensor Handling Precautions". We recommend writing them directly into the installation and commissioning checklist. "Twisted-pair / shielded cable", "centred busbar" and "symmetrical simultaneous power-up" are the three most common and most reproducible sources of zero-point anomalies on site.
- Refer to each product's datasheet for limiting parameters; exceeding them degrades performance or causes permanent damage.
- Assemble using the torque recommended in the datasheet.
- To prevent noise interference on the output signal, use twisted-pair or shielded cable for the output wiring.
- For sensors with a through-hole, install the primary busbar filling the aperture or centred in the aperture.
- Other equipment generating a magnetic field nearby may cause accuracy changes.
- The metal plating of the mating terminal should match the plating of the sensor socket.
- Electrostatic discharge may shift the zero voltage or zero current; take ESD precautions during storage, handling and use.
- For closed-loop current/voltage sensors, the positive and negative supply voltages must be equal in magnitude and applied simultaneously, otherwise the output zero point may increase.
- For closed-loop sensors the product of measured peak current and its duration is fixed; exceeding it may damage the sensor. Current consumption depends on the measured current, so verify the supply can deliver sufficient output current.
- Avoid high temperature and humidity in storage; when stored for six months or more, confirm terminal solderability before use.
What This Article Does Not State, and Why
- No customer names, project locations or acceptance measurements: the available source is a product selection catalog, which contains no measured records of a specific project.
- No residual-current trip threshold or protection coordination time: these are set by the electrical design according to the applicable standards and site earthing arrangement.
- No BMS sampling rate or protocol mapping: these depend on the BMS vendor's interface definition.
- No promised accuracy gain or energy-saving percentage: any performance statement should be based on site survey, baseline measurement and acceptance re-testing.
To configure a specific cabinet size, busbar specification, bus voltage and downstream interface, contact our engineers with the site condition list; the model and settings will then be confirmed item by item against the latest datasheets.
Frequently Asked Questions
Why must a DC panel use residual-current sensors that support a DC component? Because residual current from a DC-side insulation fault may be pure DC or pulsating DC, which a conventional AC residual-current CT cannot cover. Catalog page 9 lists "DC leakage sensors" separately for branch insulation-to-ground monitoring, and the catalog's leakage modules specify Type-B detection covering DC, AC and complex waveforms.
How do I choose between the FR fluxgate series and the CM closed-loop Hall series? By range and purpose: the catalog FR series has primary ratings down to 0.005-0.3 A and is positioned for high-accuracy small DC and leakage detection; the CM series covers 200 A to 5000 A for main circuits. They are not substitutes and often appear together in one system.
Can the module's trip-level output drive a circuit breaker directly? The catalog says it "outputs a trip level when the residual current exceeds the threshold, triggering subsequent safety action" - i.e. it provides a signal, not a breaking capability. Whether it can drive a breaker directly, or needs an interposing relay or protection circuit, must be checked in that model's datasheet and determined by the electrical design; this article does not speculate.
What does a notation like 0.01-0.02-0.05-0.1 mean in the parameter table? It is the catalog's list of selectable primary ratings for one series; the hyphen separates ratings, it is not a minus sign or a continuous range. For example FR2V offers 0.01, 0.02, 0.05, 0.1, 0.2 and 0.3 A. A specific order code corresponds to one of them - refer to the datasheet.