Home / News / Current Sensing in Solar Combiner Boxes, APF/SVG and EV Chargers: An Engineering Configuration Case

Current Sensing in Solar Combiner Boxes, APF/SVG and EV Chargers: An Engineering Configuration Case

2026-11-02Engineering Cases11 min read
Current sensor configuration for solar combiner boxes and power electronics

Sources and Scope of This Case

This article is an engineering configuration example compiled from published product documentation. It is not a construction record or acceptance report for a specific customer project, and contains no customer names, project locations, measured performance figures or acceptance conclusions. All models, ranges, supply voltages, outputs and accuracies are taken directly from the sensor selection catalog parameter tables; final selection is subject to site conditions, the latest datasheets and engineer confirmation.

  • Solar combiner box: catalog page 9, "Generation - PV" - current sensors in the combiner box mainly measure the current of each parallel branch, so the status of each PV array can be monitored, open circuits detected, and over-current/over-voltage protection provided.
  • APF: catalog page 9, "Distribution - Active Power Filter" - current sensors acquire the system harmonic current; the controller rapidly computes and extracts each harmonic order and generates a compensation current command.
  • SVG and wind: catalog page 9, "Static Var Generator" - grid-side current/voltage acquisition, inverter output current acquisition and DC-link voltage acquisition; "Wind Power" - precise measurement of DC-side and AC-side current to keep the inverter operating stably.
  • EV charging: catalog page 10, "Utilization - AC/DC Charging Piles" - single/three-phase incoming current is monitored and plays an important role in charging-process monitoring and safety; the leakage module entries also explicitly list charging piles as a suitable application.
  • VFD / UPS / motor control: catalog page 10; installation basis: page 11, "Sensor Handling Precautions"; parameter basis: the series parameter tables.

Three Operating Conditions, Three Different Measurement Goals

The applications listed on catalog pages 9-10 all look like "measure current", but the goals differ substantially: a combiner box cares about consistency across branches, an APF cares about harmonic content and response speed, and a charger cares about incoming metering and safety. Identify the operating condition before discussing models.

Operating conditionMeasurement goal (catalog wording)Selection prioritiesCatalog entry
Branch-level monitoring (solar combiner box)Current of each parallel branch → array status, open-circuit detection, over-current protectionMulti-channel consistency, size and mounting, range coveragePage 9, Generation - PV
Power-stage control (APF / SVG / wind converter)Harmonic current, grid-side/inverter-side current, DC-link voltageRated current, accuracy, response and bandwidth, supply capacityPage 9, Distribution - APF / SVG; Page 9, Wind Power
Equipment-level metering and safety (charger / UPS / VFD)Single/three-phase incoming current monitoring, charging-process safetyRange ratings, output interface, whether residual-current detection is addedPage 10, Utilization - AC/DC Charging Piles

Configuration A: Solar Combiner Box Branch Current Monitoring

The catalog defines the combiner-box requirement as "measure the current of each parallel branch → monitor array status, detect open circuits, prevent excessive current or voltage". The emphasis is consistency across branches, not extreme accuracy on a single channel. Engineering practice therefore starts from the branch rated current and the conductor / PCB mounting form, and only then chooses between ASIC SMD/PCB-mount devices and through-hole sensors.

Branch current sensing: real catalog model parameters

Model (catalog name)Primary rated range ASupply VOutputAccuracyPosition / note
AN1V PB30150-100-150-200-250-3003.30.33~2.97V±1.0Multi-variant PCB-mount ASIC, suited to multi-channel branch boards
AS1V H0050-100-200-300-400-500-60052.5±2V±1.0Through-hole housed ASIC, 5 V supply, 2.5±2 V output
CR1V PB006-15-2552.5±0.625V±0.7Low-range voltage-output through-hole closed-loop
CN1A PB0025±15±25mA±0.5PCB-mount closed-loop, 25 A rating
HK2V H0050±12…15±4V±1.0Small-range open-loop, 50 A rating

A combiner box packs many devices and parallel branches, so the page-11 requirements on "twisted-pair or shielded output cable", "primary busbar filling or centred in the aperture" and "ESD precautions" are easiest to overlook here. Route signal wiring separately from the power circuit on multi-channel boards and verify zero point and polarity channel by channel during commissioning.

  • Select the range rating from the branch fuse / cable rated current; note that hyphens in the catalog separate selectable ratings, not a continuous interval.
  • For multi-channel boards prefer 3.3 V / 5 V supplied, voltage-output ASIC or closed-loop models to avoid extra power modules.
  • For through-hole solutions confirm the aperture matches the cable / busbar dimensions and centre the primary conductor as the catalog requires.

Configuration B: Power-Stage Sensing for APF / SVG / Wind Converters

The catalog describes the APF as "acquiring system harmonic current → rapidly computing and extracting each harmonic order → generating a compensation current command"; the SVG as "grid-side current and voltage acquisition, inverter output current acquisition and DC-link voltage acquisition"; and the wind converter as "precise measurement of DC-side and AC-side current to keep the inverter operating stably". All share large measured currents, harmonic-rich waveforms and multi-point synchronous acquisition.

Closed-loop Hall current sensors are typical here: the catalog CM / CR series covers 500 A to 5000 A ratings, with open-loop extra-high-current models also available. On the voltage side, select within the VN series according to the DC-link / grid measurement point. All parameters below are read directly from the catalog parameter tables.

Current side: real catalog model parameters

Model (catalog name)Primary rated range ASupply VOutputAccuracyPosition / note
CM3A H00500±15…24±100mA±0.5500 A closed-loop, APF / inverter output side
CM4A H031200±24±300mA±0.31200 A high-current closed-loop
CM5A H002000±15…24±400mA±0.22000 A closed-loop
CM9A H001500-3500-5000±24±300~1000mA±0.31500/3500/5000 A extra-high-current closed-loop
CR8A M00500-1000-2000-4000-5000±15~24±100~1000mA±0.3Bolt-mount high-current closed-loop, 500–5000 A ratings
HK4V H00800-1000-1200-1500-2000-3000-5000±154V/5V<±1%Open-loop extra-high current, 800–5000 A ratings

Voltage side: real catalog model parameters

Model (catalog name)Primary rated range ASupply VOutputAccuracyPosition / note
VN4V P0048V52.5±2V±0.548 V bus voltage sensing
VN4A M15500V-750V-1500V-2000V±15…24±50mA±0.5High-voltage bolt-mount voltage sensor
VN4VA PB0020V154-20mA±1.04–20 mA output voltage sensor for remote transmission
VN2A P0010mA±15±25mA±0.6Low-primary-current voltage sensor

Three hard constraints for closed-loop designs (catalog page 11): positive and negative supply voltages must be equal in magnitude and applied simultaneously, or the output zero point increases; the product of measured peak current and its duration is fixed and exceeding it may damage the sensor; and current consumption depends on the measured current, so the supply must be able to deliver sufficient output current. High-frequency, high-current conditions such as APF/SVG make it essential to close these three items at the power-design stage.

Configuration C: EV Charger Incoming Monitoring and Residual-Current Protection

Catalog page 10, "AC/DC Charging Piles", states that "the single/three-phase current at the incoming end is monitored, playing an important role in charging-process monitoring and ensuring charging safety". In addition, the catalog entry for TR6A 32 C00 & FR1D 6 C00 explicitly states it is "widely applicable to single- or three-phase power systems and an ideal choice for charging piles, power monitoring and similar scenarios".

Engineering practice splits this into two circuits: incoming current metering uses open-loop / ASIC models selected by rated current and mounting form, while residual-current protection uses Type-B detection modules selected against the possible waveforms (combined AC/DC). Their outputs also differ (analogue vs level / indication) and must be handled separately downstream.

Incoming current metering: real catalog model parameters

Model (catalog name)Primary rated range ASupply VOutputAccuracyPosition / note
HS1V C0750-100-200-300-400-500-600±12…15±4V±1.0Busbar-window open-loop, 50–600 A ratings
HS2V H02200-300-400-500-600-800-1000-1200-1500±15±4V±1.0Large-window open-loop, 200–1500 A ratings
HK1V H00200-400-500-600-800-1000-2000±12…15±4V±1.0Open-loop, 200–2000 A ratings
AT4V H0050-75-100-150-200±12…15±4V±1.0Three-hole busbar ASIC, 50–200 A ratings

Residual-current protection: catalog leakage modules

Model (catalog name)FormKey capability per catalogTypical position
TR6A 32 C00 & FR1D 6 C00 一体式漏电检测模组Residual-current sensor + metering CT integratedType-B detection, low power, high immunity, single/three-phase; catalog lists charging piles and power monitoringCharger incoming circuit needing both metering and leakage detection
FR5D 6 C00 漏电流检测传感器Open-loop fluxgate leakage sensorThrough-hole, DC/AC/pulsating residual current, push-pull indication above threshold, built-in self-test coilAC charger residual-current protection
FR1D 6 C02 剩余电流传感器Residual-current sensorType-B detection circuit, multiple leakage waveformsDC charger or space-constrained circuits
  • AC and DC chargers produce different residual-current waveforms; confirm the required detection type first, then match it to the Type-B capability stated in the catalog.
  • The FR5D series has a built-in test coil for functional self-test; if the maintenance procedure requires periodic self-test, include this in the acceptance checklist.
  • A level / indication output is not a breaking capability; driving capability and protection coordination must be checked in the datasheet and set by the electrical design.

Engineering Configuration Checklist

The checklist below is derived from catalog page 11, "Sensor Handling Precautions", and the three configuration examples above. We recommend running through it once at design review and again at commissioning / acceptance.

  • Check the measured rated current and possible peaks: confirm the selected rating covers them without approaching the catalog's "peak current × duration" limit.
  • Confirm supply voltage and output form: 3.3 V/5 V single supply, ±12…15 V dual supply, current output, voltage output, CAN, 4-20 mA - all matched to the downstream acquisition.
  • For closed-loop sensors, confirm symmetrical simultaneous power-up and verify the supply's output current capability.
  • Use twisted-pair or shielded cable for outputs; keep signal wiring away from power circuits and equipment generating magnetic fields.
  • For through-hole types, confirm the primary conductor fills or is centred in the aperture; for bolt/busbar types, assemble to the datasheet's recommended torque.
  • Confirm the mating terminal plating matches the sensor socket plating, and follow ESD precautions for storage and handling.
  • Check the operating temperature range (e.g. the catalog lists -40 to 85 °C for FR8V) against actual cabinet conditions.
  • Remember that pictures and parameters are for reference; obtain the latest datasheets before volume ordering.

What This Article Does Not State, and Why

  • No customer names, project locations or acceptance measurements: the available source is a product selection catalog containing no measured records of a specific project.
  • No harmonic compensation ratio, power-factor improvement or measured metering accuracy: these are system-level commissioning results requiring on-site measurement.
  • No charger residual-current trip threshold or protection coordination: these are set by the electrical design according to applicable standards.
  • No promised energy-saving percentage or accuracy gain: any performance statement should be based on site survey, baseline measurement and acceptance re-testing.

To configure a specific number of combiner-box channels, bus voltage, cabinet size and downstream interface, contact our engineers with the site condition list; models will then be confirmed item by item against the latest datasheets.

Frequently Asked Questions

Should a combiner box use ASIC sensors or closed-loop Hall sensors? It depends on mounting form and range. Catalog ASIC models such as AN1V / AS1V use 3.3 V or 5 V supplies with voltage outputs in PCB-mount or through-hole housings, which suits dense multi-channel boards. Closed-loop models such as CN1A / CR1V use ±15 V dual supplies with current or voltage outputs and suit standalone through-hole mounting. If the board offers only a single supply and has many channels, the ASIC route simplifies wiring and power.

Why are closed-loop solutions preferred for APF harmonic current acquisition? The catalog describes the APF as "acquiring system harmonic current → rapidly extracting each harmonic order → generating a compensation current command", which demands measurement that follows the waveform and covers a large range. The catalog CM / CR closed-loop series covers 500 A to 5000 A ratings. Open-loop extra-high-current models can also be used, but the accuracy/response trade-off must be confirmed against the controller requirements.

Can incoming current metering and residual-current protection in a charger use the same sensor? Usually not. The former measures the main-circuit rated current (tens to thousands of amperes); the latter measures mA-level residual current and must discriminate DC/AC/combined waveforms. The catalog's TR6A 32 C00 & FR1D 6 C00 integrates a residual-current sensor and a metering CT in one module - that is two measurement functions in one housing, not one sensor covering both ranges, and both channel interfaces still need to be confirmed separately.

Is a catalog range such as 1500-3500-5000 an interval? No. The catalog uses hyphens to separate the selectable primary ratings offered by one series; for example CM9A offers 1500, 3500 and 5000 A ratings. It is not a minus sign, nor a continuously adjustable 1500-5000 A range. A specific order code corresponds to one of these ratings - refer to the datasheet.

Related reading

FAQ

Should a combiner box use ASIC sensors or closed-loop Hall sensors?

It depends on mounting form and range. Catalog ASIC models such as AN1V / AS1V use 3.3 V or 5 V supplies with voltage outputs in PCB-mount or through-hole housings, which suits dense multi-channel boards. Closed-loop models such as CN1A / CR1V use ±15 V dual supplies with current or voltage outputs and suit standalone through-hole mounting. If the board offers only a single supply and has many channels, the ASIC route simplifies wiring and power.

Why are closed-loop solutions preferred for APF harmonic current acquisition?

The catalog describes the APF as "acquiring system harmonic current → rapidly extracting each harmonic order → generating a compensation current command", which demands measurement that follows the waveform and covers a large range. The catalog CM / CR closed-loop series covers 500 A to 5000 A ratings. Open-loop extra-high-current models can also be used, but the accuracy/response trade-off must be confirmed against the controller requirements.

Can incoming current metering and residual-current protection in a charger use the same sensor?

Usually not. The former measures the main-circuit rated current (tens to thousands of amperes); the latter measures mA-level residual current and must discriminate DC/AC/combined waveforms. The catalog's TR6A 32 C00 & FR1D 6 C00 integrates a residual-current sensor and a metering CT in one module - that is two measurement functions in one housing, not one sensor covering both ranges, and both channel interfaces still need to be confirmed separately.

Is a catalog range such as 1500-3500-5000 an interval?

No. The catalog uses hyphens to separate the selectable primary ratings offered by one series; for example CM9A offers 1500, 3500 and 5000 A ratings. It is not a minus sign, nor a continuously adjustable 1500-5000 A range. A specific order code corresponds to one of these ratings - refer to the datasheet.

Need a similar solution?

Our engineers survey site conditions and design the solution; configuration and results are based on on-site measurement.