Home / Projects / Commercial RO Purified Water System with Online Water Quality Monitoring

Commercial RO Purified Water System with Online Water Quality Monitoring

Industry:Food and beverage / commercial purified water Location:Northern Vietnam Scale:Commercial RO purified water system + online water quality monitoring Timeline:2 weeks scheme design + installation and commissioning2026-11-01
Commercial RO Purified Water System with Online Water Quality Monitoring

Note:These cases are compiled from typical industry scenarios. Customer names are withheld under commercial confidentiality agreements; equipment quantities shown are typical configuration ranges, and performance descriptions are subject to site survey data and acceptance re-testing, and are not offered as committed values.

Project overview

Application type
Commercial purified water production (beverage preparation, direct drinking water)
System composition
Pre-treatment + reverse osmosis + post-treatment + online monitoring
Monitoring items
Conductivity, product water flow, operating pressure, liquid level
Delivered scope
Water quality analysis, system configuration, installation and commissioning, O&M handover

Project Background

The customer uses water for beverage preparation and staff direct drinking, with the raw water being a mix of municipal tap water and water from an on-site well. The previously used small purification units had two problems: the product water quality fluctuated, and filter cartridge replacement was judged by operator experience, which had led to cartridges being over-run and water quality deteriorating.

The project objective is to hold the product water quality steadily within the required range while making filter cartridge replacement evidence-based and the water quality traceable.

Current Situation and Difficulties

  • Fluctuating raw water quality: the hardness and salinity of the well water vary with the seasons, so a fixed-configuration system produced water with elevated conductivity during certain periods.
  • Uneven demand curve: water use is concentrated during production hours, and the gap between peak flow and average daily flow is large, so system capacity and buffer design must match.
  • No basis for cartridge replacement: replacing cartridges on a fixed schedule may be premature and wasteful, or may over-run them during peak periods.
  • Lack of records: product water quality was not recorded continuously, so the cause could not be traced when an anomaly appeared.

Scheme Design

1. Analyze the raw water first, then fix the configuration

  • A complete raw water analysis was performed (hardness, alkalinity, conductivity, turbidity, residual chlorine, iron and manganese, microbiological indicators), with multiple samples taken across seasonal variation.
  • The pre-treatment process and membrane element configuration were determined from the worst-case water quality rather than the average, avoiding exceedances during extreme periods.

2. Targeted pre-treatment for the actual raw water problems

  • Turbidity and particulates: multi-media filtration plus cartridge filtration to protect the downstream membrane elements.
  • High hardness: softening or antiscalant dosing to prevent scaling on the membrane surface.
  • Residual chlorine: activated carbon filtration to avoid oxidative damage to the membrane elements.
  • Iron and manganese: targeted oxidation and filtration treatment.

3. RO unit and capacity matching

  • Production capacity was determined jointly from peak and average daily water demand, with raw water and product water tanks providing buffering to avoid frequent starts and stops of the unit.
  • The number and arrangement of membrane elements were set by the required recovery rate and salt rejection rate, and the concentrate discharge ratio was calculated from the raw water salinity.
  • The high-pressure pump, membrane housings, piping and instruments were selected according to operating pressure and hygienic requirements.

4. Online monitoring and data recording

  • Conductivity: online monitoring on both the product water and concentrate sides directly reflects desalting performance, making it the primary indicator for judging membrane performance decline.
  • Flow: product water flow and concentrate flow are used to calculate the recovery rate and to detect membrane fouling.
  • Pressure: inter-stage pressure and pre-membrane pressure; a rising differential pressure indicates fouling or scaling.
  • Level and start/stop: the raw water and product water tank levels are interlocked to prevent dry running and overflow.

The data is fed to local display and recording, forming a traceable operating curve that provides the basis for cartridge replacement and cleaning decisions.

Typical Configuration (subject to water analysis and site survey)

  • Pre-treatment: multi-media filtration, activated carbon filtration, softening or antiscalant dosing, cartridge filtration
  • RO unit: membrane elements and high-pressure pump configured to the production capacity, including membrane housings, piping and valves
  • Post-treatment: disinfection and terminal filtration configured according to the end use
  • Online instruments: conductivity meters, flow meters, pressure gauges, level transmitters
  • Control and recording: local control cabinet plus operating data recording
  • Buffering and supply: raw water tank, product water tank and supply pumps

Implementation Process

  1. 1Water analysis and demand survey: take multiple water samples for analysis and tabulate peak and average daily consumption and the distribution of usage periods.
  2. 2Scheme and configuration confirmation: determine the process and capacity from the worst-case water quality and peak flow, and define the instrumentation and recording requirements.
  3. 3Installation and piping work: position the equipment, connect piping and electrical supply, paying attention to hygienic-grade piping and drainage slope.
  4. 4Commissioning and trial operation: flush the pre-treatment, commission the membrane elements and set the parameters, then run continuously while observing the product water indicators.
  5. 5O&M handover: define the cartridge replacement criteria, cleaning conditions, recording requirements and daily inspection items.

Results and Verification

  • Stable water quality: product water conductivity is recorded continuously within the set range, and anomalies are traceable.
  • Evidence-based cartridge replacement: replacement timing is judged from the operating differential pressure, product water flow decay and cumulative production volume, replacing a fixed schedule.
  • Visible operation: key parameters are recorded continuously, and abnormal periods can be replayed to find the cause.
  • Handover-ready O&M: inspection checklists and replacement criteria are documented, so staff changes do not affect operating quality.

Note: the specific process and capacity must be based on the raw water analysis report, the water demand curve and site conditions; no fixed product water target is promised at the scheme stage.

Reusable Lessons

  • Design for the worst-case water quality: a system configured for average water quality will inevitably exceed limits when the water quality varies.
  • The conductivity meter is the most important instrument: it reflects both desalting performance and membrane condition, and although it is inexpensive, it delivers the greatest value.
  • Buffer design is often underestimated: insufficient tank capacity causes the unit to start and stop frequently, affecting membrane life and product water stability.
  • Write the cartridge replacement criteria into the handover documents: a schedule kept in someone's memory breaks down as soon as that person leaves.

Results and verification

Traceable water quality
Product water conductivity and operating parameters recorded continuously
Evidence-based cartridge replacement
Replacement timing judged from differential pressure, flow decay and cumulative production volume
Matched configuration
Process and capacity determined from worst-case water quality and peak flow
Handover-ready O&M
Inspection checklists and replacement criteria documented

Related projects

Need a similar solution?

Our engineers survey site conditions and design the solution; configuration and results are based on on-site measurement.